As of January 2022, HughesNet’s average download speed is 17.44 Mbps. ![]() These metrics are the most important indicators of broadband connection performance. The dials above will display statistics on download and upload speed. This speed test will check the capability of your broadband connection whether you use HughesNet or another provider. Resetting your router or call HughesNet customer service for additional assistance. If your HughesNet speed test result is lower than expected, try Note: This speed test can be used to test any internet provider, not What the heck.Whether HughesNet is your internet provider or you use a different provider, the speedĬan show key statistics about your internet connection. So now what? They gave me a deal on the newest modem at a discounted price. The weather is beautiful here and I checked and its beautiful in Utah. Its all about the weather they are telling me. I have 8 calls in to them and they won't admit it but they can't fix this issue. They rebooted the modem four times, 4 different techs and the call was dropped because I have the Hughs phone service. I've had this trouble for over a month and I doubt Utah has had storms every minute of every day and night for a month and a half. Utah is where my gateway to the internet is located. I called tech dept at Hughes and the did their regular tests and told me there were storms in Utah. A test of the connectivity showed limited conductivity and when checked five minutes later it showed good connectivity, then bad again a minute after that. All of a sudden one day, and I wrote the date down, I started to lose internet capabilities. I suspect they have done some alteration with "their" equipment or have made some adjustment on the sattellite or such. It started just a month and a half ago and that is coinciding with the complaints from other Hughes users. I have had Hughes for years and have never experienced anything like this ever. SOA minimum for too large (302400) - recommended <= 86400.ĭone testing SOA parameters for. SOA expire for too small (432000) - recommended >= 604800. SOA retry for OK (14400) - recommended >= 3600. ![]() SOA refresh for OK (86400) - recommended >= 14400. Successful attempt to deliver email for SOA RNAME of (no_) using TTL for too small (1800) - recommended >= 3600. Name server (139.85.4.15) not checked for legacy name server ID.ĭone testing name server .īegin testing SOA parameters for. Name server (139.85.4.15) not checked for zone transfer of. Name server (139.85.4.15) authoritative for. Name server (139.85.4.15) does not answer queries over TCP. Name server (139.85.4.15) answers queries over UDP. Reverse for 139.85.4.15 points to an unknown host name (). ![]() Name server (69.35.42.42) authoritative for .īegin testing name server. Name server (69.35.42.42) answers queries over TCP. Name server (69.35.42.42) answers queries over UDP. ![]() Name server (69.35.42.41) answers queries over TCP. Name server (69.35.42.41) answers queries over UDP. This second paragraph is only my personal warning about the DirecTV receiver (mine's a Genie).Ĭould not find reverse address for 69.35.42.41 (41.42.35.69.in-addr.arpa.). It's something I try to warn other people about before they take that leap. The only way I could get things back to normal was to do a complete factory reset, losing everything on the DVR and losing all of my settings. I learned this the hard way after just trying on demand to see what it was like after upgrading to Gen5. It also causes it to try to connect to the internet when you do searches, and, strangely enough, will continue to even after a network reset. And even if you later reset the network on the device to disconnect it from the WiFi, it will annoy you with constant reconnection recommendations. Connecting Hughesnet (or any ISP with a data cap) to such a device is usually recommended against for this reason.Įdit: In addtion, if you have not previously had the DirecTV receiver connected to WiFi, you'll notice that, when you do, a few things change on it. And turning off power on such a device doesn't really turn it off, it just puts it in standby mode, allowing it to still be connected to your WiFi and still use data. Be VERY careful if you are going to connect to a DirecTV receiver, as there is no way to control the data they use and they use it for more than just on demand. Isn't regarding your problem, but only something you mentioned, and that's that you were trying to connect to a DirecTV receiver.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |